Waterthane Super 100 Floor Seal / Varnish

Share
Waterthane Super 100 Floor Seal / Varnish
Waterthane Super 100 Floor Seal / Varnish image 2
Waterthane Super 100 Floor Seal / Varnish image 3
Waterthane Super 100 Floor Seal / Varnish image 4
Properties:
Fast curing
High chemical resistance
Clear flexible finish
Quick recoating properties
Excellent abrasion resistance
Very low odour
Easily maintained
Conforms to BS EN 14904 (gloss finish only)

Description:
WATERTHANE SUPER 100 floor seal / varnish is specially developed unmodified 100% water based Polyurethane seal for wood and cork flooring that will provide a clear, flexible, abrasion and chemically resistant finish which is easily maintained.
Available in Gloss, Satin and Matt finish.

Uses:
WATERTHANE SUPER 100 floor seal / varnish has been developed for use on new or resanded Hardwood, Mosaic, Block, Cork and Softwood flooring, and produces a hard wearing and chemically resistant finish that is easily maintained. It is suitable for use in both commercial and domestic areas, and for recoating pre-finished flooring.

WATERTHANE SUPER 100 Gloss floor seal / varnish has also been tested to conform to the spec BS EN 14904 (Surfaces for sports areas - Indoor surfaces for multi-sports use - Specification) which refers to the procedure and standard of slip resistance within BS EN 13036-4:2003

Preparation/Application:
Apply WATERTHANE SUPER 100 floor seal / varnish evenly using an applicator, roller or soft brush. Take care not to leave pools, runs or drip marks, which will detract from the overall appearance of the floor. If the floor is to be left overnight before recoating, it is important that the surface is lightly abraded using a suitable grade of sandpaper or sandscreen / mesh disc to ensure good adhesion of the finish.
Once final coat has been applied, the floor should be left for a minimum of 48 hours prior to light traffic being permitted. The finish will continue to harden for a period of 5 days.
Cleaning chemicals should be avoided during this period.

Cleaning, Abrading & Resealing:
Floor surfaces should be scrubbed with an alkaline degreasing solution, rinsed and neutralised with FLOORTECH NEUTRAL FLOORCLEAN. The floor should then be rinsed clean and allowed to dry thoroughly. When dry apply a coat of WATERTHANE SUPER 100 floor seal / varnish and allow to dry (2–3 hours depending on temperature and humidity). Apply a second coat within 24 hours to obtain maximum adhesion between coats. Ensure that there is adequate ventilation whilst the seal is drying. The coating should be allowed to cure for 48 hours before allowing light traffic.
When over coating previously finished floors, two coats of WATERTHANE SUPER 100 floor seal / varnish are recommended.

Sanding & Sealing:
Ensure that the floor surface is free from oil, wax, grease, dirt and previous treatments. After sanding ensure all dust has bee removed by vacuuming or tac ragging. Floors which have been previously waxed or oiled it is recommended a primer coat of FLOORTECH PRE-SEAL is used to prevent rejection or to reduce porosity. Apply a first coat of WATERTHANE SUPER 100 floor seal / varnish and allow to dry (2–3 hours depending on temperature and humidity). Any Line/court marking should be completed at this stage if required. Raising may occur on some types of wood grain and it will be necessary to buff back, in which case the first coat should be left for 3 to 4 hours.
Apply a second coat and third coat (if required) of WATERTHANE SUPER 100 floor seal / varnish within 24 hours of each other to obtain maximum adhesion between coats.
Ensure that there is adequate ventilation whilst the seal is drying. The coating should be allowed to cure for 48 hours before allowing light traffic.
When coating refurbished Wood, Cork or Chipboard floors, three coats of WATERTHANE SUPER 100 floor seal / varnish are recommended to provide a hard wearing finish.

Note: If Line/court paint is use that is not ‘Floortech products line paint’ then a trial test must be done to ensure compatibility between the paint and the Waterthane.

Maintenance:
The sealed floor should be damp mopped or a Scrubber/drier used with a solution of FLOORTECH NEUTRAL FLOORCLEAN. To prevent the build up of grease / fatty matter on the surface of the coating it should be scrubbed periodically with a mildly alkaline solution, such as FLOORTECH MULTI-PURPOSE FLOOR CLEANER.

Coverage:
Approximately 10 – 20 sqm per Litre depending on porosity of the surface.

Drying Time:
3 hours depending on temperature, humidity and ventilation.

Shelf Life:
2 years if left unopened. Stored in a cool, dry place & protected from frost.

Discounts:
2.5% Discount on 10 Litre Packs
5% Discount on 20 Litre Packs
For further Quantity Discounts please call 01773 828111 or Email for a quotation.
Telephone Orders: 01773828111
From
£13.33 ex VAT
Waterthane Super 100 - 1 Litre - Gloss
£13.33 ex VAT
Waterthane Super 100 - 1 Litre - Matt
£13.33 ex VAT
Waterthane Super 100 - 1 Litre - Satin
£13.33 ex VAT
Waterthane Super 100 - 2.5 Litre - Gloss
£20.83 ex VAT
Waterthane Super 100 - 2.5 Litre - Matt
£20.83 ex VAT
Waterthane Super 100 - 2.5 Litre - Satin
£20.83 ex VAT
Waterthane Super 100 - 5 Litre - Gloss
£34.17 ex VAT
Waterthane Super 100 - 5 Litre - Matt
£34.17 ex VAT
Waterthane Super 100 - 5 Litre - Satin
£34.17 ex VAT
Waterthane Super 100 - 5 Litre x 2 - 10 Litre Pack - Gloss
£66.63 ex VAT
Waterthane Super 100 - 5 Litre x 2 - 10 Litre Pack - Matt
£66.63 ex VAT
Waterthane Super 100 - 5 Litre x 2 - 10 Litre Pack - Satin
£66.63 ex VAT
Waterthane Super 100 - 5 Litre x 4 - 20 Litre Pack - Gloss
£129.85 ex VAT
Waterthane Super 100 - 5 Litre x 4 - 20 Litre Pack - Matt
£129.85 ex VAT
Waterthane Super 100 - 5 Litre x 4 - 20 Litre Pack - Satin
£129.85 ex VAT

Related Products/Accessories

Recently Viewed Items [clear]